Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Blog Article
The writer is making a few great pointers related to A Step-by-Step Guide to Installing a Bathtub in general in the content following next.

Installing a bathtub isn't specifically rocket science, yet it does need solid plumbing, woodworking, and in some cases, tiling skills. Changing an old tub with a new one is additionally a reasonably challenging project. If the old bathtub is easily easily accessible, the task can move easily; if you have to open up a wall to get rid of the old bathtub and place the brand-new bath tub, the task is much harder. In either instance, the job is within a house handyman's skills, although you will certainly need an assistant to leave the old tub as well as set in the new one. See to it you have certified on your own for the work and also fit trying it. Instead of employing a service provider to take control of a halfway-completed job, it is far better to think about using one prior to you begin. Chances are you may require a professional plumber to make tube connections.
This short article will aid you install a new tub in your restroom if you have actually already bought a new bathtub as well as don't require to transform the setup of your previous water system pipes.
Your tools and material list should consist of the following:
Getting ready for the Installation
Firstly, the sustaining framework supplied with the bathroom needs to be fitted (if required) according to the producer's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is very important to make certain that if the faucet includes a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the taps device to avoid strain on the tub.
Fit the flexible tap ports to the bottom of both faucets utilizing 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. See to it you make use of all of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to currently prepare to be fitted in its final placement.
Removing Old Taps
If you need to replace old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the water system. After doing so, activate the faucets to drain pipes any type of water continuing to be in the system. The procedure of removing the existing faucets can be quite problematic as a result of the restricted accessibility that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a fabric all set for the staying water that will certainly come from the pipes. When the supply pipes have actually been eliminated, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the solitary taps from transforming during this procedure. When the faucets have been removed, the holes in the bath/basin will need to be cleaned up of any kind of old sealing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Utilizing the two wood boards under its feet, position the bathtub in the called for position. The wood boards are practical in evenly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 little points.
The next objective is to make sure that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bathtub up until the level reviews level.
To install taps, fit all-time low of the outermost adaptable tap connector to the suitable supply pipe by making a compression sign up with; after that do the exact same for the various other faucet.
Switch on the water system and also examine all joints as well as brand-new pipework for leakages and tighten them if necessary. Fill the bathtub as well as also inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Finally, deal with the bathroom paneling as defined in the maker's user's manual. Tiling and securing around the bath tub must wait up until the bath tub has been utilized a minimum of when as this will certainly resolve it into its final placement.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to stop damage to the thread. One end of the connector fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the mounting hole in the bath/basin guaranteeing that the washers are in location between the faucet and the sink. Safeguard the tap in position with the supplier supplied backnut. Once the tap is securely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind needs to be connected to the tap finishes first, tightening up only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom meets the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to crack a stiff seal, causing the water to penetrate the wall in between the bath and the tiling, leading to complications with moisture and also feasible leaks to the ceiling listed below.
You can select from a range of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes and also cartridges, as well as can securing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill up the bath tub with water prior to securing, to enable the motion experienced when the tub remains in use. The sealant can split fairly early if you do not think about this movement before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily offered on the marketplace. It is advisable to fit the tiles making use of waterproof or water resistant glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
I discovered that blog post on Tools You Need to Install a New Bathtub when doing a lookup on the web. So long as you liked our blog entry kindly don't forget to pass it around. We cherish reading our article about Installing A Bathtub.
Course Detail Report this page